specification model dc voltage rated current rated power output voltage adj. range note.6 current adj. range line regulation load regulation setup, rise time note.8 hold up time (typ.) voltage range note.5 frequency range power factor (typ.) efficiency (typ.) ac current (typ.) input inrush current( .) typ leakage current safety standards note.7 working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over current note.4 over voltage over temperature can be adjusted by internal potential meter or through output cable 1500ms, 80ms / 115vac 0ms, 80ms / 230vac at full load at full load 100 16ms/230vac 16ms/115vac at full load 90 ~ 305vac 127 ~ 431vdc 47 ~ 63hz pf>0.98/115vac, pf>0.95/230vac, pf>0.92/277vac at full load (pl ease refer to "power factor characteristic" curve) 0.43a / 115vac 0.24a / 230vac 0.23a / 277vac cold start 70a/230vac <0.75ma / 277vac 95 ~ 108% protection type : constant current limiting, recovers automatical ly after fault condition is removed -40 ~ +70 (refer to "derating curve") 20 ~ 95% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 60 ) 10 ~ 500hz, 5g 12min./1cycle, period for 72min. each along x, y, z axes 336.5khrs min. mil-hdbk-217f (25 ) 171*61.5*36.8mm (l*w*h) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. constant current operation region is within 60% ~100% rated output vol tage. this is the suitable operation region for led related application s, but please reconfirm special electrical requirements for some specific syste m design. 5. derating may be needed under low input voltages. please check the static c haracteristics for more details. 6. type a only. 7. safety and emc design refer to en60598-1, cns15233, gb7000.1, fcc part 18. 8. length of set up time is measured at cold first start. turning on/off the powe r supply may lead to increase of the set up time. 9. the power supply is considered as a component that will be operated in combi nation with final equipment. since emc performance will be affected by th e complete installation, the final equipment manufacturers must re- qualify emc directive on the complete installation again. 0.73kg; 20pcs/15.6kg/0.8cuft protection type : shut down o/p voltage, re-power on to recover 40w single output switching power supply universal ac input / full range (up to 305vac)built-in active pfc function protections: short circuit / overload / over voltage / over temperature cooling by free air convection ocp point adjustable through output cable or internal potential meter ip67 / ip65 design for indoor or outdoor installations three in one dimming function (1~10vdc or pwm signal or resistance) suitable for led lighting and moving sign applications compliance to worldwide safety regulations for lighting 5 years warranty suitable for dry / damp / wet location or outdoor application features : h l g - 4 0 h s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment safety & emc protection 85 10 (rth2) protection type : shut down o/p voltage, re-power on to recover selv ip65 ip67 blank : ip67 rated. cable for i/o connection. ul8750, en61347-1, en61347-2-13 independent ; approved ; design re fer to ul60950-1, tuv en60950-1 ip65 or ip67 f m m 110 withstand voltage isolation resistance i/p-o/p:3.75kvac i/p-fg:1.88kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh constant current region note.4 hlg-40h-12 a a : ip65 rated. output voltage and constant current level can be adjusted thr ough internal potential meter. b : ip67 rated. constant current level adjustable through output cable w ith 1~10vdc or 10v pwm signal or resistance 18 ~ 24v 15 ~ 21v 23 ~ 30v 28 ~ 35v 35 ~ 43v 41 ~ 49v 48 ~ 58v 59 ~ 66v 54 ~ 63v 87% 87% 88.5% 88.5% 89% 89% 90% 90% 90% 2.5% 2 ~ 3.33a 2.0% 1.6 ~ 2.67a 1.0% 1.2 ~ 2a 1.0% 1 ~ 1.67a 1.0% 0.8 ~ 1.34a 1.0% 0.67 ~ 1.12a 1.0% 0.5 ~ 0.84a 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 2.0% 1.5% 1.0% 0.5% 0.5% 0.5% 0.5% 1.0% 0.45 ~ 0.75a 0.5% 0.5% 1.0% 0.58 ~ 0.96a 0.5% 0.5% 12v hlg-40h-12 hlg-40h-15 hlg-40h-20 hlg-40h-24 HLG-40H-30 h lg-40h-36 hlg-40h-42 hlg-40h-48 hlg-40h-54 7.2 ~12v 15v 9 ~ 15v 20v 12 ~ 20v 24v 14.4 ~ 24v 30v 18 ~ 30v 36v 21.6 ~ 36v 48v 28.8 ~ 48v 3.33a 2.67a 2a 1.67a 1.34a 1.12a 0.84a 39.96w 40.05w 40w 40.08w 40.2w 40.32w 40.32w 150mvp-p 150mvp-p 13.5 ~ 17v 150mvp-p 17 ~ 22v 200mvp-p 22 ~ 27v 200mvp-p 27 ~ 33v 200mvp-p 33 ~ 40v 300mvp-p 44 ~ 53v 10.8 ~ 13.5v 54v 32.4 ~ 54v 0.75a 40.5w 300mvp-p 49 ~ 58v 42v 25.2 ~ 42v 0.96a 40.32w 200mvp-p 40 ~ 46v compliance to en55015, en61000-3-2 class c ( 60% load) ; en61000-3-3 compliance to en61000-4-2,3,4,5,6,8,11; en61547, en55024, hea vy industry level (surge 4kv), criteria a emc immunity emc emission d : (option) : ip67 rated. timer dimming function, contact mean well for deta ils. file name:hlg-40h-spec 2011-05-30
mechanical specification case no.957b unit:mm ip67 rated. cable for i/o connection. ip65 rated. output voltage and constant current level can be adjusted thr ough internal potential meter. (can access by removing the rubber stopper on the case.) 300 20 300 20 fg (green/yellow) fg (green/yellow) svt 18awg 2c svt 18awg 2c 36.8 36.8 sjtw 18awg 3c sjtw 18awg 3c ac/l(brown) ac/l(brown) ac/n(blue) ac/n(blue) 4.2 4pl 4.2 4pl 300 20 300 20 -v(black) -v(black) +v(red) +v(red) io vo adj adj 9.6 9.6 11.9 11.9 147.2 147.2 171 171 61.5 61.5 46.5 46.5 32 32 73.6 73.6 t case: max. case temperature. t case: max. case temperature. 30.75 30.75 40w single output switching power supply h l g - 4 0 h s e r i e s a type:(hlg-40h-_a) blank:(hlg-40h) file name:hlg-40h-spec 2011-05-30
300 20 fg (green/yellow) 36.8 sjtw 18awg 3c ac/l(brown) ac/n(blue) 9.6 11.9 147.2 171 61.5 46.5 32 -v(black) +v(red) dim-(white) dim+(blue) 4.2 4pl svt 18awg 2c 300 20 derating curve static characteristics input voltage (v) 60hz 90 100 125 135 145 155 165 175 180 200 230 305 100 90 80 70 60 50 40 load (%) fosc : 100khz block diagram 230vac input only ambient temperature ( ) load (%) -40 -25 0 -10 15 30 50 60 70 20 40 60 80 100 (horizontal) 73.6 t case: max. case temperature. 30.75 dim+ (b type) dim- detection pwm & pfc circuit o.l.p. o.t.p. emi filter rectifiers power switching filter & rectifiers +v -v i/p fg control o.v.p. & o.l.p. pfc circuit ul 2517 18awg 2c 40w single output switching power supply h l g - 4 0 h s e r i e s b type:(hlg-40h-_b) file name:hlg-40h-spec 2011-05-30
0 .8 5 0 .8 6 0 .8 7 0 .8 8 0 .8 9 0 .9 0 .9 1 0 .9 2 0 .9 3 0 .9 4 0 .9 5 0 .9 6 0 .9 7 0 .9 8 0 .9 9 1 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 % 2 7 7 v a c 2 3 0 v a c 1 1 0 v a c 70 72 74 76 78 80 82 84 86 88 90 92 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 277vac 230vac 110vac hlg-40h series possess superior working efficiency that up to 90% can be re ached in field applications. efficiency vs load (48v model) there are two major kinds of led drive method "direct drive" and "with led driv er". typical led power supply i-v curve a typical led power supply may either work in "constant voltage mode (cv) or c onstant current mode (cc)" to drive the leds. mean well's led power supply with cv+ cc characteristic can b e operated at both cv mode (with led driver, at area (a) and cc m ode (direct drive, at area (b). driving methods of led module vo(%) 100 60 50 95 (max.) io (%) constant voltage area constant current area hiccup protection (a) (b) (c) power factor characteristic load efficiency (%) pf load constant current mode (40w) 40w single output switching power supply h l g - 4 0 h s e r i e s file name:hlg-40h-spec 2011-05-30
direct driving : under direct driving, the power supply will work in "constant current mod e (cc)" and output voltage of the power supply will be clamped by sum of forward voltage (v ) of the led strip. f the total forward voltage of series connecting leds is suggested for 60%~ 95% of power supply rated output voltage due to concern of the best pf value and efficiency. ac source i/p o/p hlg-40h with led driver using additional driver, the power supply will work in "constant voltag e mode (cv)" and output voltage of the power supply will be kept in rated value. in this drive mode, several design issues need to be considered: 1.output voltage of psu must be higher than total forward voltage of series c onnecting leds by 3v minimum. 2.input capacitor (cin) of led driver circuit should use 47uf ~ 100uf(typ .) of rating depends on the operating frequency of the led driver. the higher the operating frequency is used, the smaller value of cin should b e chosen, and vice versa. ac source i/p o/p ic circuit cin cout v f r l hlg-40h ~ ~ ~ ~ 3.do not use b type with led driver. fg (green/yellow) ac/l(brown) ac/n(blue) -v(black) +v(red) dim-(white) dim+(blue) hlg-40h b type 60k 60% 60% 10k 10k /n 20k /n 30k /n 40k /n 50k /n 60k /n 70k /n 80k /n 90k /n 100k /n single driver multiple drivers (n=driver quantity for synchronized dimming operation) 1v 4v 7v 2v 5v 8v 3v 6v 9v 10v 10% 10% 20k 20% 20% 30k 30% 30% 40k 40% 40% 50k 50% 50% 70k 70% 70% 80k 80% 80% 90k 100k open open open 90% 90% 100% 100% resistance value dimming value percentage of rated current percentage of rated current reference resistance value for output current adjustment (typical ) please do not connect "dim-" to "-v". 1 ~ 10v dimming function for output current adjustment (typical) 60% 60% 10% 10% 20% 20% 30% 30% 40% 40% 50% 50% 70% 70% 80% 80% 90% 90% 100% 100% duty value percentage of rated current 95%~105% ----- 95%~105% 95%~105% 10v pwm signal for output current adjustment (typical): frequency ra nge :100hz ~ 3khz dimming operation(for b-type only) ip67 rated. output constant current level can be adjusted through outpu t cable by connecting a resistance or built-in 3 in 1 dimming function, 1 ~ 10vdc or 10v pwm signal between dim+ and dim-. 40w single output switching power supply h l g - 4 0 h s e r i e s file name:hlg-40h-spec 2011-05-30
~~ ac source i/p fg c b d a a o/p led cc driver chassis of led lamp cc ic hlg-40h a. add a common mode ferrite choke on output wires to reduce the common emissi on between 10m ~ 300mhz per lighting emi regulation. b. chassis of led lamp and chassis of hlg-40h or the fg wire should be connected to t he safety ground to reduce the emi noise, including the conduction and radiation emission. c. the additional x-cap and discharge resistor can reduce the l conduct ion noise between 9k ~ 1mhz per lighting emi regulation. d. l-c filter should be added at the dc input of led constant current driver to av oid the differential emission and high frequency noise generated by the cc driver. ow frequency emi debug suggestion dimming connection diagram for turning the lighting fixture on/off : using a switch and relay can turn on/off the lighting fixture. using the built-in dimming function on b-type model can't turn the lighti ng fixture totally dark. please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the led power s upply unit. 1.output constant current level can be adjusted through output cable by c onnecting a resistor or 1~10vdc or 10v pwm signal between dim+ and dim-. 2.the led lighting fixture can be turned on/off by the switch. n fg l relay blue brown green/ yellow ac/l ac/n hlg-40h b type dim+ dim- v(-) v(+) blue white black red switch adjuster 0~100k ohms resistance 1~10v dc voltage 10v pwm signal led lighting fixture 40w single output switching power supply h l g - 4 0 h s e r i e s file name:hlg-40h-spec 2011-05-30
waterproof connector waterproof connector can be assembled on the output cable of hlg-40h to ope rate in dry/wet/damp or outdoor environment. hlg-40h i/p o/p led lamp ac source cable joiner pin configuration (female) pin configuration (female) size size m12 m15 4-pin 5a/pin m12-04 order no. order no. 10a max. suitable current suitable current 5-pin 5a/pin m12-05 10a max. 2-pin 12a/pin m15-02 12a max. up to four wires can be connected through this cable joiner bysoldering or clamping by tools. 66 26 20 25 suitable for 14awg~22awg o/p wires led lamp hlg-40h waterproof connection 40w single output switching power supply h l g - 4 0 h s e r i e s file name:hlg-40h-spec 2011-05-30
|
